How was the braking system 1000 years ago? The evolution of the braking system

Sep 20, 2024

Leave a message

Recently, everyone must have heard about the two incidents of brake failure of the Xiaomi SU7 on the race track, with some people saying that the SU7 is not a racing car, who allowed it to run on the race track? By using the standard for racing cars, you are not just bullying the car. Others say that many civilian cars run on race tracks, but they don't all go up the wall.

 

Who is to blame for the wall-climbing incident is not what we are discussing here. Xiaomi's official response is that the wall-climbing incident occurred because of brake thermal degradation and excessive wear. Let's talk about how the car's braking system has developed over the years.

 

-1

 

Back in ancient times when people drove horse-drawn carriages, fueling up was basically done by pulling, turning was basically done by grabbing, honking was basically done by mouth, and braking was basically done by leg, of course, the leg of the horse. Later, in countless blood and tears lessons, people finally realized that if they went downhill all the way, relying solely on the horse's leg brake would not only be a waste of the horse's energy, but the person might also be in danger.

 

-2

 

Thus, the earliest braking system was born, where people used a piece of wood as the brake lining and rubbed it against the wheel to provide stopping power. Although sometimes the wood would smoke when the brake was applied, it was still sufficient for slower-moving carriages. In fact, a similar structure is still used today, such as the rim brake on bicycles, although the friction surface has been changed from the tire to the rim, the principle is similar.

 

-3

-4

 

Since the steam engine appeared in the 18th century, vehicle power was switched from animals to machines, and the speed was getting faster and faster, but the brakes didn't change much. Until the early 20th century, the braking system principle for carriages, trains, and early automobiles was still basically the same as that of horse-drawn carriages. What was the result? Even flat ground became difficult to handle! Fortunately, a genius appeared in 1900, William Maybach. He designed the first automotive drum brake. You are familiar with this, right? Until now, some trucks and low-end passenger cars still use drum brakes.

 

-5

-6

 

It just so happened that only two years later, in 1902, another genius, Frederick William Lanchester, designed the earliest disc brake, which is the brake structure used by more than 80% of cars today, including the Xiaomi SU7. Did you think that the disc brake appeared decades later than the drum brake? In fact, it did not. Because the disc brake has higher requirements for the material of the brake pads, early disc brakes used iron pads and copper pads, and copper wears very quickly. Imagine that you are happily preparing for a family road trip, bringing sunflower seeds, beer, playing cards, and three sets of brake pads. Wouldn't that be a little disappointing? So, as long as the material and manufacturing technology were not improved, the disc brake could not be popularized.

 

-7

-8

 

However, the drum brake is not without its own problems. Its poor heat dissipation ability and tendency to suffer heat decay are structural defects that cannot be changed, and the same is true for the drum brake today. Therefore, as the material and manufacturing technology improved, people began to consider the disc brake again. The early popular brake pad material was asbestos, but this material has a fatal defect: it is not environmentally friendly. The fine fibers of asbestos that wear off can be inhaled into the lungs and cause irreversible damage. As a result, the asbestos roof tiles that were very common when I was young are no longer available. At the same time, because asbestos is an insulating material, it has poor heat conduction, and the brake pads heat up quickly after friction, making it difficult to cool down.

 

-9

-10

 

Later, semi-metallic brake pads were introduced, which replaced the asbestos in the original pads with steel wool to increase hardness. However, this time the heat dissipation was too good, and the brake pads would heat up after just a few steps. The brake system was always in a high temperature state, causing the rubber seals, hoses, and other components on the calipers to deteriorate extremely quickly. Additionally, the water in the brake fluid would turn into gas at high temperatures, causing the brakes to soften. Furthermore, the metal fibers in the brake pads would rub against each other, generating noise at low speeds, and causing the pads to rust easily when it rained.

 

-11

-12

 

In light of these defects, a new generation of products emerged, low-metal brake pads. As the name suggests, they contain less metal fiber, so their wear resistance is not as good, but their braking performance is better than semi-metallic brake pads, and the noise is lower. They are usually used in cars that prioritize comfort. Later, ceramic-based brake pads were introduced, using ceramic fibers as the reinforcing material. This is a higher-end brake pad, with good heat resistance, so the friction stability is good, and the noise is low because there is no metal. The lack of metal also means that no metal powder will be left on the wheel hub, which is difficult to clean. The disadvantage is obvious - it is expensive!

 

-13

14

 

However, ceramic brakes are not the most expensive, there is an older brother above it: carbon-based brakes. Carbon-based brakes include carbon-ceramic and carbon-carbon, one is a composite of carbon fiber and ceramic fiber, and the other is all carbon. Although the two have slightly different properties, they both have no shortcomings in general: good heat conduction, high temperature resistance, strong braking power, lighter and more wear-resistant, so carbon-based brakes are basically equipped on racing cars, high-end sports cars, or aircraft. To be honest, they have little to do with ordinary people.

 

-15

 

In addition to the brake pads, engineers have also put effort into the brake discs of the disc brake. In terms of materials, they have gone from cast iron, alloys, organic materials to the most advanced carbon fiber materials, and in terms of structure, they have gone from the original single disc to later designs with ventilation channels, drilled holes, and grooves for fast heat dissipation and the removal of brake dust, gradually improving braking performance.

 

-16

-17

 

Having talked so much about disc brakes, it seems that drum brakes have no chance of making a comeback. And that's true... They lose out on their structure. They're heavier, less efficient at cooling, and don't offer the same convenience in rapid, continuous braking as disc brake designs. They're also not as compatible with high-tech features like ABS. But drum brakes do have their advantages. First, they have strong stopping power. Two pads, one going in the direction of the rotating drum and the other against it, create a self-locking effect when braking. The more you brake, the tighter the pad grips the drum, which is where they win on their own structure. Plus, they're cheaper. In recent years, there haven't been many big expenses aside from some changes to the friction material. So drum brakes are very popular in low-end cars and heavy-duty trucks. They don't mind the poor cooling performance, as they can spray water on the brakes for heavy-duty trucks. Hey, you said you'd make a Redmi version with drum brakes and put the heavy-duty truck spray water system on it. That would be fast on the race track!

 

-19